Boat carpet,
fitted dockside.
Catamaran, yacht, barge: we fabricate in our Villedoux workshop and fit dockside in La Rochelle, La Flotte and Rochefort. Materials compliant with IMO FTP and MED, marine polyurethane adhesives, heat-welded seams. 28-plus years of craftsmanship.
“An indoor carpet laid with acrylic adhesive lasts 18 months on a boat. A properly fitted marine carpet lasts 10 years. The difference is not the textile, it is everything underneath the textile.”
Four cases, four approaches.
Sailing or power catamaran
Two hulls, a central saloon exposed to sun and salt. We use 100% non-absorbent polypropylene carpet, with cutting adapted to the curves of the saloon and the central beam skirts. See our dedicated catamaran page.
Motor yacht or luxury sailing yacht
Wide saloons, owner's cabins, premium finishes. A combination of fire-treated wool carpet and bespoke rugs, blended into the existing joinery and leatherwork. Tolerant of engine vibration.
Liveaboard or commercial barge
Flat, apartment-like surfaces, strong river humidity but no salt. For restaurant and events barges, the inland-waterway public-venue fire rating applies (Bfl-s1 minimum).
Full refit of a leisure craft
We strip out the old flooring, often laid with standard acrylic adhesive that never holds on a boat. We treat the substrate, relay with a marine polyurethane adhesive and heat-weld the seams. The floor lasts.
A project in mind?
Every boat calls for its own answer.
Catamaran, yacht or barge: Valentin Prévoteau comes dockside to take the measurements and price it right.
Six constraints a living-room carpet never meets.
Air on board swings between 80 and 95% relative humidity. Salt settles on the surface then migrates into the fibres. On an unsuitable covering, mould appears under the floor within 12 to 18 months. Polypropylene absorbs next to nothing.
In a fire on board, evacuation takes time. The IMO FTP Code sets limits on smoke toxicity and spread rate. For private leisure craft, Bfl-s1 is the baseline. For charter and commercial use, IMO Part 5 certification is mandatory.
On a leisure craft, every kilo aboard affects the waterline, fuel use and behaviour at sea. We favour carpets of 800-1100 g/m², without a heavy felt underlay but with a fine closed-cell foam.
Rounded hull, manifold, complex cabin shapes: fitting straight standard lengths is impossible. Templating on film, millimetre workshop cutting, heat-welded seams to prevent any water ingress.
A standard indoor acrylic adhesive dries, shrinks with temperature swings and gives way under salt. We use only marine-certified single or two-part polyurethane adhesives, compliant with ISO 9239.
Engine vibration, thermal expansion between a cool bilge and a sun-heated deck: a marine floor has to absorb all this without lifting. Closed-cell foam backing, an elastic adhesive, flexible seams. That is also why the work is done in the workshop then adjusted dockside, never improvised.
Catamaran, yacht, barge, an overview.
Three families of material, one single standard.
On the brand side, we work with the European contract and marine specialists: Bolon (Sweden, woven vinyl floors), Roberts Marine, as well as the contract ranges from EGE and Gerflor that can be adapted to the marine world with additional certification. No mainstream entry-level product pushed beyond its intended use: we see too many boats redone three times in five years for exactly that reason.
“Every boat is different. No template is ever reused. A dockside visit is a must before any serious pricing.”
Twelve terms to know before any quote.
Marine vocabulary can feel opaque. Here are the standards, fibres and techniques we routinely cite in a quote or an inland-waterway public-venue file. They are also the questions any serious safety commission will ask.
European reaction-to-fire rating for floor coverings (EN 13501-1): B = very low contribution to fire, fl = floor, s1 = low smoke emission. The minimum baseline for leisure craft.
International Maritime Organization, Fire Test Procedures. The worldwide reference for marine fire testing. Part 5 deals specifically with floor coverings on passenger and commercial vessels.
Marine Equipment Directive 2014/90/EU. The ship's-wheel mark applied to materials approved for commercial navigation in Europe. Mandatory for professional charter and on-board events.
The radiant-panel test that measures the critical flame-spread flux of a floor covering. The higher the kW/m² value, the more the material resists.
The former French reaction-to-fire classification (M0 non-combustible, M4 easily flammable). Still quoted in inland-waterway public-venue files. Rough equivalence: M1 ≈ Bfl-s1, M2 ≈ Cfl-s1.
Fibre Reinforced Polymer. The polyester/glass-fibre composite that makes up 90% of modern leisure hulls. A non-porous substrate that requires a specific primer before bonding.
A manufacturing process where needles punch the fibre into a primary backing, then fix it with latex or a secondary backing. Most contract and marine carpets are tufted.
High-end weaves, historically British. Axminster = pattern by the metre, ideal for yachts with a large saloon. Wilton = dense looped velvet, 15 to 28 years of service life.
A 100% hydrophobic synthetic fibre (moisture regain < 0.05%). Unaffected by salt, dries within hours. The reference fibre in the marine world.
A technical nylon, more abrasion-resistant than PP but with 4-5% moisture regain. Reserved for ventilated saloons and air-conditioned spaces.
A seam-sealing technique for marine PVC floors: a thermofusible cord is inserted into a groove then melted at 200°C with a welding iron. The seam becomes continuous and watertight.
A two-component polyurethane adhesive (resin + hardener) with a 30 to 60 minute pot life. It holds through temperature swings (-20 to +80°C), stays elastic and resists salt. The marine reference.
The finest ports in France and Monaco.
Our workshop is based in Villedoux, near La Rochelle. We travel across France and as far as Monaco for premium projects. Call-outs are organised by project, with a mobile team for high-end work outside our home area.
Port Hercule and Port de Fontvieille. Work on owners' yachts and premium charter craft.
Vieux-Port and Port Canto. Winter refits during the between-season lay-ups.
Port Saint-Tropez. Coordination with local cabinetmakers and trimmers on full finishing projects.
Port Vauban, Europe's leading superyacht harbour. Workshop fabrication and dockside fitting on a tight schedule.
Port Lympia. Private leisure craft and coastal cruising motor yachts.
Port de la Capte and Port d'Hyères. Sailing bases and access to the Îles d'Or.
Vieux-Port, Estaque, Pointe Rouge. Cruising yacht and charter catamaran refits.
Port des Minimes, the largest marina on the Atlantic coast. Workshop in Villedoux, 10 minutes away.
Port des Sablons. Channel leisure craft and large cruising yachts.
Port-Deauville. Work on yachts and craft wintered in Normandy.
Larmor-Plage marina. Southern Brittany, a historic racing and cruising base.
Arcachon marina. The bay and the southern Atlantic coast.
Five steps, the fit scheduled around you.
Templating on film, photos, substrate moisture reading, identification of the tricky points (manifold, curves, service runs). Discussion with the owner or skipper.
Chosen at our Villedoux showroom or from samples sent out. We confirm the fire ratings required by use (private leisure, charter, commercial).
Detailed quote within 48 hours. Scheduling built around the boat's refit window or its dockside availability. No surprises on the final invoice.
Cutting and preparation in our Villedoux workshop from the templates. Millimetre precision to avoid any reworking on site. The layout is tested before transport.
Final fit aboard the boat, marine polyurethane adhesive, heat-welded seams, finishes around thresholds and inspection hatches. Handed back clean.
Boat carpet, technical answers.
What fire standards apply to marine floor coverings?+
For private leisure craft, the European Bfl-s1 rating (reaction to fire plus low smoke emission) is the recommended minimum baseline. For commercial craft (charter, passenger vessels), you must comply with the IMO FTP Code (International Maritime Organization, Fire Test Procedures) Part 5, as well as the MED 2014/90/EU directive (Marine Equipment Directive). We supply the material certificates with every fit.
Why not use a standard indoor carpet on a boat?+
Three technical reasons. First, fibres such as untreated wool or standard polyamide absorb ambient humidity (80-95% on a boat) and eventually grow mould under the floor. Second, indoor acrylic adhesives do not hold up to temperature swings and the salt-laden atmosphere. Third, the indoor Cfl-s1 fire rating falls short of marine requirements. The result at 18 months: lifting, odour, damage to the substrate.
Which material for which boat?+
100% polypropylene for wet areas, salt-exposed zones, or heavily used spaces (sailing catamaran, cruising yacht). Fire-treated wool for the ventilated, air-conditioned saloons of motor yachts. Welded marine PVC for galleys, heads and gangways. On a boat, you often combine two or three materials depending on the zone.
Does the boat have to be lifted out of the water for the fit?+
No, in most cases. The fit is done dockside, over 1 to 3 days depending on the surface area. We coordinate the work with the marina (La Pallice, Port des Minimes, La Flotte, Saint-Martin) or the yard. For a full refit involving stripping out the old flooring and treating the substrate, the boat may be out of the water (dry dock, boat hoist).
How long does a properly fitted marine carpet last?+
On a leisure craft used seasonally (June to September), a marine polypropylene carpet fitted by the book lasts 8 to 12 years. On a yacht in permanent use, expect 5 to 8 years depending on how often it is lived in. The failures we come across rarely come from wear. They almost always come from a poorly prepared initial fit, with the wrong adhesive or an absorbent underlay.
Do you work in ports beyond La Rochelle?+
Yes. Our workshop is in Villedoux, 10 minutes from La Pallice and Port des Minimes. We regularly work in Rochefort, Royan, La Flotte, Saint-Martin-de-Ré, Boyardville and Marennes. By quote, we travel as far as Arcachon, Les Sables-d'Olonne or southern Brittany for larger craft.
Do you have references in the marine sector?+
Our 28-plus years of experience at CB Sols include work on catamarans from the Lagoon and Bali fleets in La Rochelle, several private yachts at Port des Minimes, and liveaboard barges on the Charente. Project details remain confidential out of respect for the owners, but we can share references on a serious enquiry.
A boat to fit out? Let's talk.
Dockside visits in the ports of La Rochelle, Île de Ré and Rochefort. A bespoke quote after a precise survey.