CB Sols Flooring
CB Sols
Coverings · La Rochelle
Language
FRENES
ServicesFor businessesFor homeownersArchitectsProjectsShowroomBrandsAboutAreas
06 85 05 28 80Free quote
CB Sols→FAQ
Vinyl Flooring

What are the standards for vinyl flooring in a professional kitchen?

Short answer

A professional-kitchen vinyl floor must be rated R10 or R11 (anti-slip), resistant to grease and disinfectants, heat-welded (zero seams) and compliant with HACCP requirements. Gerflor Mipolam Granit and Taralay Premium are the benchmarks.

The HACCP standard and its implications for the floor

HACCP (Hazard Analysis Critical Control Point) is the food-safety management system mandatory in all professional catering establishments. For floors, it requires:

- An impermeable covering: no porosity that would let bacteria take hold - A smooth or lightly textured surface: effectively cleanable with no retention zones - No wide or accessible joints: cement joints are a source of bacterial contamination - Resistance to cleaning and disinfection products: concentrated alkalis, chlorinated disinfectants, acids

Heat-welded sheet vinyl meets all these requirements. It is the HACCP solution par excellence: no visible joint, 100% impermeable, resistant to the products commonly used in kitchens.

Tiling with epoxy joints can also be HACCP-compliant, but maintaining the relief is more demanding. Tiling with cement joints is technically non-compliant with HACCP.

The anti-slip classification: required by labour law

French labour law (articles R4214-1 et seq.) requires anti-slip floor coverings in premises with a slip risk. Professional kitchens are classed as high-risk premises.

The German R classification (DIN 51130) is the reference: R9 (low risk), R10 (moderate risk), R11 (high risk with oils and grease), R12 (very high risk).

For the different zones of a kitchen: - Dining room (dry zone): R9 minimum - Standard kitchen: R10 minimum - Frying zone, wash-up, hot wet zone: R11 mandatory - Vegetable unpacking and washing zone: R11-R12

CB Sols systematically selects R11-minimum products for all professional kitchens. A slippery kitchen floor is a workplace accident waiting to happen.

Heat welding: technique and necessity

Heat welding is a technique that creates a watertight junction between two sheets of vinyl flooring by melting a weld cord (of the same composition as the floor) into the groove machined between the two sheets.

Why it is mandatory in a kitchen: without a weld, the junction between two sheets is a joint which, however tight, lets liquids, grease and micro-organisms seep under the covering. In a professional kitchen, subject to high-pressure cleaning, that seepage is inevitable and rapid.

Heat welding requires specific equipment (a welding gun and calibrated nozzles) and technical training. CB Sols trains its fitters in this technique and carries out the welding on all its professional-kitchen projects.

Coved skirtings (the welded vinyl running 10 to 15 cm up the walls) complete the watertightness by eliminating the floor/wall junction, another critical contamination point.

The benchmark products and their certifications

Three families of products suit professional kitchens:

Gerflor Mipolam Granit: homogeneous vinyl, standard R10 rating (R11 on request), P2 chemical resistance, NSF certification for food spaces. A wide range of colours. Lifespan: 20-30 years.

Gerflor Taralay Premium Contract: homogeneous vinyl, R10/R11 rating, certified for catering venues, very low VOC emissions (Indoor Air certification). Comparable lifespan.

Gerflor Taralay Impression Compact: heterogeneous vinyl, R10, high chemical resistance, many designs. A good option for kitchens where looks come first with sufficient resistance.

CB Sols supplies all three brands and can show you samples at the showroom or during an on-site visit when quoting.

Related questions
Laying Technique
Can carpet be laid over existing tiles?
Read →
Your project

A question about your project?

CB Sols replies within 24h, free quote within 48h

Free quote06 85 05 28 80